This app isn't in any of our charts yet.
Subwoofer box calculator & speaker box design: bass reflex, ports, cut sheet.
Boxsmith is a subwoofer box calculator and speaker box design app that works the way desktop tools do, on your phone: it simulates how your driver plays in a sealed, ported (bass reflex) or bandpass box, sizes the port, and draws up the cut sheet. All of that is free: no subscription, no account, no paywall on the results, and it works offline. SIMULATION, NOT JUST A VOLUME - Full Thiele-Small model of the driver and box, the same family of model desktop box-design programs use - Graphs: response (SPL), maximum SPL, cone excursion against Xmax, port air speed, impedance and group delay - Set the amplifier power, a subsonic filter, a low-pass, bass boost and car cabin gain - Max SPL that stops where the cone hits Xmax, the power rating or the port starts to chuff - Overlay up to four designs and compare them side by side in a table THE RIGHT BOX FOR YOUR SUB - Sealed, ported and 4th-order bandpass boxes - "Suggest a box" finds flat, deeper-bass and compact designs for your driver, keeping the port buildable - Warnings in plain words: past Xmax, a port that will chuff, a port pipe resonance or box standing wave in your band, a load too low for the amp - Multiple subs in one box, single or dual voice coils, every wiring option with its final load PORTS DONE PROPERLY - Slot or round ports, one or several, with the end correction included - Port length for any tuning; one tap sizes the port to stay under the air-speed limit - Tells you when the port needs an L-shaped bend BUILD IT - Enter the width and height that fit your trunk or room and fit the depth to the volume - Wedge (sloped back) boxes for trucks and hatchbacks - Net volume after the drivers, port and bracing are taken out, checked against the design - 3D preview, cut list in inches and fractions or millimetres, double baffle, port panels - Sheet layout on 4 × 8 ft or metric sheets with your saw kerf, and a PDF cut sheet YOUR DRIVERS - Type the T/S parameters from the spec sheet in any common units; Boxsmith works out the rest - Every value is cross-checked: it warns when Qts disagrees, when Vas looks like cubic feet typed as litres, or when Xmax looks peak-to-peak - Share a driver as a file with a friend; import theirs TOOLS - Amp gain setting with a multimeter: the target voltage for your amp and load, test tones at 0, -3, -6 or -10 dB (the level is always stated) and a slow sweep for rattles, played over Bluetooth or saved as WAV files for a USB stick - Subwoofer wiring calculator: up to 16 subs, 0.5 to 16 ohm coils, amps stable to 0.25 ohm - Port length and tuning, box volume, quick sealed box - Passive crossover values (1st to 4th order), L-pad and Zobel BOXSMITH PRO (OPTIONAL, ONE-TIME) - Transmission-line (T-line) boxes: line length or tuning, taper, driver position and mouth air speed, simulated as a real duct, with a fold plan and the dividers in the cut list - Isobaric pairs (clamshell or tunnel): half the box for the same bass, parallel or series - Passive radiator boxes with the mass to add for your tuning - 6th-order bandpass: both chambers vented, each with its own tuning and port - Measured in-car response: import your car's transfer function and every graph uses it - One purchase, no subscription, and it removes ads. Everything else stays free YOUR DATA STAYS YOURS - Everything is stored on your phone: no account, no cloud - Back up every driver and design to one file and restore it on a new phone In English, Spanish, Portuguese, German, French and Italian. Imperial or metric. The simulation uses the standard lumped model with 25 °C air; real boxes differ a little, so check your build before you cut. Subwoofer box calculator, speaker box design, bass reflex calculator, ported box calculator, T-line box, port length calculator, car audio enclosure design: Boxsmith, free and ad-supported, from Fernhart Labs.
past month, based on 1 day
Downloads
Low confidence138
From install count ÷ months since release
In-app revenue
Low confidence$93
From downloads × revenue per download
Ads
$30
$15 – $61
Estimate, ads (benchmark-based, not calibrated per app)
Total
$123
In-app + ads
Google Play only. Downloads from daily Top free ranks (or the store's install count); in-app revenue from Top grossing ranks, calibrated on AppTweak's US estimates, or else from downloads; ads from public ad benchmarks. Not reported figures.